BETAFPV 65 Pro 2 OSD Whoop Brushless Drone Quadcopter FrSky

BETAFPV 65 Pro 2 OSD Whoop Brushless Drone Quadcopter FrSky

Product description

BETAFPV Beta65 Pro 2 OSD Whoop Brushless Drone Quadcopter FrSky

Beta65 Pro 2 is the smaller version of the Pro series. With the flight control AIO F4 2S and the brushless motors 0802 it weighs only 24 g without batteries. BETAFPV always tries to give every FPV pilot more choice. The Pro Series is our product line with lighter, faster and more integrated brushless drones.

X-Series like Beta65X or Beta75X stands for the highest performance of 2S Whoop drones. With long-range RX, powerful controls and engines, pilots would fly the X-drone like a smaller mini-drone. Pro Series, such as Beta65 Pro 2 and Beta75 Pro 2, have a higher integrated AIO FC and lower weight. Pilots fly like a faster Tiny Whoop drone. This is the biggest difference between the drones of the X series and the Pro series.

The Beta 65 Pro 2 launches a new era of 2S Whoop drones. Compared to the Beta75 Pro 2 it is 4g lighter and 10mm smaller. With the high-performance STM32F411 processor FC boards and betaflight_matekf411rx_4.0.0 (development version), everyone was able to fly the Beta75 Pro 2 drone like a racing pro. You get the BETAFPV 65 Pro 2 ready assembled, no soldering or tinkering needed. Lightest 0802 17500KV motors with cable connectors. Just plug it in and go. By default 2pcs 300mAh HV 1S high performance batteries are recommended.

Technical specifications

• Weight: 24g (without battery)
• Frame: Beta65X frame
• Engines: 0802 17500KV with plug
• Propeller: 31 mm stanchions with 4 blades, 1.0 mm shaft hole
• Camera: small AIO camera
• Receiver option: SPI Frsky
• Battery: 300mAh 1S HV batteries 2pcs

FC & ESC data

CPU: STM32F411

• Six-Axis: MPU6000
• Size: 26mm x 26mm, Whoop mounting pattern
• Firmware version: betaflight_matekf411rx_4.0.0 (development version)
• OSD: Built-in BetaFlight OSD (STM32 controls OSD chip via SPI in DMA mode)
• For the VTX radio control, a smart audio connection is available
• Built-in 1-2S regulator with 5A continuous current and 6A peak current
• Supports BLHeliSuite programmable
• Factory firmware: S_H_50_REV16_7.HEX

AIO camera VTX

• The Beta65 Pro 2 is the lighter AIO VTX camera with only 2.9 g. Output: 25mW
• The radio control includes a Smart Audio function
• Antenna: Dipole ANT
• Frequency: 5.8 GHz 6 bands 48 channels, with raceband: 5362 ~ 5945 MHz
• TV system: PAL
• Field of view: 100-120 degrees with 1/4 lens

ADAPTED AIO CAM & VTX
The AIO camera VTX of the Beta65 Pro 2 is a customized version of Z02. The VTX board and camera board are split and feature a 35-degree camera mount for faster flying. 25mW power is available from stock. In addition, it has almost all the other functions of the Z02 camera, such as Smart Audio, etc.

FAQ
1. Does this drone have a current sensor?

This drone has NO real current sensor. We use the virtual electricity meter in Betaflight. If calibrated properly, it can be accurate enough to be useful. Here is the precalibrated value from the box.

set current_meter = VIRTUAL
set ibatv_scale = 90
set ibatv_offset = 29

2. The bonding method for F4 2S AIO (SPI Frsky RX) can be found on our support page.

3. Cli dump for different versions of the 2S Whoop can be found on our support page.

4. The camera angle is 35 degrees by default, but the drone also has a replacement camera mount with 25 degrees.

5. If you are using an EU-LBT firmware wireless controller, you may find that you can not connect to this SPI-Frsky receiver. Here are the solutions we offer for you.

content
1x Beta65 Pro 2 BNF 2S Whoop Quadcopter
2x 300mAh 1S HV battery (not for PNP version)
1x replacement camera mount with 25 degree tilt