Free shipping from 120 €**
Ordered in the morning, shipped immediately!
Fachhändler

BetaFPV F4 Brushless Flight Controller ESC Stack V1 BLHeli_32

10% discount
The article is no longer available.
  • 68,00 € *
  • 75,90 €

BetaFPV F4 Brushless Flight Controller ESC Stack V1 BLHeli_32

Product description

BetaFPV F4 Brushless Flight Controller ESC Stack V1 BLHeli_32

After several months of research, the best combination of F405 4S Brushless Flight Controller with BLHeli_32 16A ESC was launched, which fully supports the 4S performance at constant power. BLHeli_32 16A ESC is adapted for the Whoop drone Beta85X. In the meantime, Beta85X is currently the first microdrone with a BLHeli_32 ESC.
BLHeli_32 is the third generation of ESC firmware after BLHeli and BLHeli_S, written for ESCs with 32-bit MCUs. With the increase in computing power, BLHeli_32 would allow faster input signals with lower latency and higher update rate, like Dshot1200!

Technical data

  • CPU: STM32F405 (overclocking to 240MHz)
  • Six axes: MPU6000
  • Size: 26 mm x 26 mm, mounting pattern
  • Firmware version: BETAFPVF405 (BEFH)
  • OSD: Built-in BetaFlight-OSD (STM32 controls the OSD chip via SPI in DMA mode)
  • RX3 and TX3 are equipped with automatic inverter and support all RX including TBS Micro RX
  • TX01 and RX01 ports are available for Frsky F-Port, DSM2/DSMX
  • Buzzer solder pads
  • Supports programmable LED like WS2812 etc.
  • Weight: 4,2g

Technical data ESC

  • Support for BLHELI_32
  • Supports PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
  • Input voltage: 3-4S lipo
  • Cotinue current: 16A
  • Peak current: 19A
  • Firmware target: BETAFPV-16A-32bit
  • MCU: STM32F051K66
  • Motor connector: 1.25 mm male connector
  • Weight: 4.4 g (7.7 g with XT30 cable)

HOW MAN FC & ESC ADJUSTMENT In order
to facilitate installation and reduce offset PIN mounting, we have added a connector for the ESC connection. Separate installation, in case the muturvibration between FC and ESC could interfere.

HOW TO ADD MAN FC & LED BOARD To
make installation easier, we have added a connector for connecting LED boards.

RECOMMENDED RECEIVER CONNECTION To
make installation easier, we have added a port for the RX connector. All ports are available on this card. So you can connect any receiver on the card. For example.

  • Frsky XM/XM+ receiver
  • Flysky receiver
  • TBS receiver
  • DSMX receiver

Content

  • 1 * F405 4S Brushless Flight Controller
  • 1 * 16A BLHeli_32 ESC
  • 1 * 4P cable for RX
  • 1 * 3P cable for LED board
  • 4 * screws M1,4x4mm
  • 4 * 1.2 mm anti-vibration rubber dampers
Bestellnummer BET-00313483-1
EAN 4260449989274
Hersteller BetaFPV

Der FPV24 Newsletter. Kein Nonsens. Maximal einmal im Monat. In Deinem Postfach.

Rabatte, Angebote, News und neue Produkte. Jetzt kostenlos für den FPV Newsletter anmelden.

Shopping Cart